ASTM B164 PDF

ASTM B specification covers Nickel Copper Alloys like Monel Alloy Round Bar with ASTM B UNS N in the form of hot-worked and cold- worked. Designation: B – 03 Standard Speci?cation for Nickel-Copper Alloy Rod, Bar , and Wire1 This standard is issued under the?xed. Monel is a corrosion resistant NiCu easily machined, and fabricated. ASTM B, ASTM B, QQ-N Class A, UNS N Available in bar, wire.

Author: Nikorn Kazigis
Country: Lithuania
Language: English (Spanish)
Genre: Career
Published (Last): 18 August 2014
Pages: 42
PDF File Size: 10.65 Mb
ePub File Size: 18.61 Mb
ISBN: 979-4-66160-357-4
Downloads: 98558
Price: Free* [*Free Regsitration Required]
Uploader: Jumuro

The materials for rod, bar, or sstm shall conform to the mechanical properties specified by the reference material. The allowances for hot-worked material in Table 5 are recommended for rods machined in lengths of 3 ft 0.

Spot grinding is permitted to remove minor surface imperfections. Workmanship, Finish, and Appearance 8. Asmt sections under 1? In case of dissatisfaction with the results of the test, the producer or supplier may make claim for a rehearing.

ASTM B – 03() Standard Specification for Nickel-Copper Alloy Rod, Bar, and Wire

E All sizes 85 84 87 84 84 80 85 55 50 60 55 50 50 8B 10B 10B 20 20 20B,C 20 — — — — — — 80 75 75 — 70 — — UNS N 40 40 30 — 25 — — 30D 30 25 — 35 — — — — — B 75 to B95 — B 60 to B75 — Cold-worked as worked or stress-relieved: Excellent resistance to chloride ion stress corrosion cracking.

This standard has been approved for use by agencies of the Department of Defense. Rejection should be reported to the producer or supplier promptly and in writing. Applications Feed water and steam generator tubing.

Material shall be tested using a square, rectangular, or circular transducer having an effective area of one square inch or less, but no dimension shall be smaller than the diameter of the reference hole. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

  CONSTITUTIO CRIMINALIS THERESIANA PDF

Cladding for the upper areas of oil refinery crude columns. E Forging quality is furnished to chemical requirements and surface inspection only. Intended primarily for hot heated bolts but is of somewhat inferior quality, as to surface seams and cracks compared to forging quality, see X1.

No tensile properties are required. The scanning path shall be circumferential or helical with the b1644 directed along a radius of the rod. Astmm name of the material or UNS Number, heat number, condition temperASTM Bthe size, gross, tare, and net weight, consignor and consignee b64, contract or order number, or such other information as may be de? C Applicable to 3 ft 0. ASTM B specification covers nickel-copper alloys the form of hot-worked and cold-worked rod, bar, round bar and wire.

Resistance to neutral, alkaline and acid salts is shown, but poor resistance is found with oxidizing acid salts such as ferric chloride.

Villares Metals International

Number of Tests It is in the form of hot-worked and cold-worked. Regular temper, under 1? Propeller and pump shafts. Dimensions and Permissible Variations 7.

The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. If you feel that your comments have not received a fair hearing you should make your satm known to the ASTM Committee on Standards, at the address shown below.

A low corrosion rate in rapidly flowing seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions. Monel Round Bars have high strength properties, heat treatable, good corrosion resistance, formability and weldability.

Examples of such requirements include, but are not limited to, the following: The rod shall then be rotated slowly against the indicator, and the deviation from straightness in any portion of the rod between the supports shall not exceed the permissible variations prescribed in Table Longitudinal strip specimens shall be prepared in accordance with Test Methods E 8 for rectangular bar up to 1? Your comments are invited either for revision of this standard or for additional standards and should b1664 addressed to ASTM International Headquarters.

  LA GUERRA MODERNA ROGER TRINQUIER PDF

Rod and bar, all sizes Rings aztm disks Forging quality: Number of Tests S. The distance between the jaws of the testing machine, with the specimen in place ready for testing, shall be not less than 10 in. One test per lot shall be performed for chemical analysis, tension test, hardness test, and wrapping test.

The material shall conform to the chemical composition limits specified by the reference material. Good resistance to sulfuric and hydrofluoric acids. The alloy has been used in a variety of applications. It is particularly resistant to hydrochloric and hydrofluoric acids when they are de-aerated. Our entire round bar inventory is available in random lengths or can be cut to specific lengths to meet your exact requirements. One test per lot shall be performed for chemical analysis, tension test, hardness test, and wrapping test.

In the event of disagreement on the degree of back re?

The position and amplitude of the response from each note shall be marked on the instrument screen or a transparent overlay, and these marks shall be used as the evaluation reference. Type C-3 for finishing. Monel Round Bars is a nickel-chromium alloy bar that contains supplemental amounts of columbium, iron, molybdenum, aluminum, and titanium.

For each lbs. All wire shall wrap around a rod of the same diameter astj the wire without cracking All wire up to 0.

Common uses of Monel include deployment in gas turbines, subservice safety valves, aircraft engines, thrust reversers, and industrial fasteners. Hot-worked material to be machined in longer lengths should be speci?

If two choices decimals are possible, as when the digits dropped are exactly a 5, or a 5 followed only by zeros, choose the one ending in an even digit, with zero de? Last previous edition approved in as B – ast